Відео

Does both wire give power? I can use this for my horn remote buy connect yellow or white to my trigger horn??

I have a '21 1000-4 talon with live valve. It has the turning radius of a school bus 😂

thats great man. i may just copy that thing. got the same bumper and tailgate waiting for install rt now.

Hello, Are you interested in testing our products? We would like to invite you to test the Front Windshield for your Honda Talon 1000R ( if your car year is 2019-2022

Thanks for doing this great video! We shared it on the Inferno Cab Heaters Facebook page today.

Russell, what happened to necessitate pulling the sub trans?

I unbolted my front diff moved it forward enough for the front diveshaft to clear then pulled the trans put the bottom. Took me about an hour to do it. Just have the remove the 2 studs and it can come right out the bottom. Very easy.

At least you don't have to remove the front diff like on the 2 seater. That's pretty cool.

My 19 service manual calls for gear oil in the sub trans. As does the user manual. What year is your 4 seater?

Can you make a video on how to adjust the shifter cable with the aftermarket shift gate?

Jackson Racing….. Fly by night… here today gone tomorrow..

So basically don’t get a talon

Hello, Are you interested in testing our products? We would like to invite you to test the Rear Windshield for your Honda Talon 1000R ( if your car year is 2019-2023

what did you do to run your exhaust on the Jackson kit they told me you have to run stock exhaust. or it gets to much boost. no warranty

How were you able to pull the basket out mine is stuck in there

I have been thinking about a Pro R, can you do a video on it? I am totally in the same boat as you. Would you also recommend keeping a talon and a Pro R? Thanks, your videos are awesome!

Is there a part link on the honda powersports website?

Thank you!

Do not pry the axle out of the diff. Plunge and pull on the shaft. You can crack the diff housing by prying on it

Russell, i went the extreme metal products route on this one because the honda one was so expensive. I do have the oem glass windshield. I noticed the wiper motor mounts the same way. I now noticed that with the bracket between the plastic my windshield does not seal on the bottom like it did before. Did you have this problem?

When installing do the primary drive gear teeth slide all the way into the other gear? Like completely flush? I have about an 1/8in difference. I’ve tried about 15 times. Unless that front guide gear keeps falling out of one clutch plate .

If my clutches are burnt up would that cause it to not re learn?

I'm shocked - I would have never bet the thing can only go 75. My Pioneer is governed to 66

where did you buy your ball joints?

10k miles?! That's amazing! Great video! Looking forward to more!

where did you get the gas cans?

So I watched this video and said "I can do that" So I did it and now im pulling my motor out of my talon. Without being able to at least plastigauge the rod bearings there is no way to ensure proper seating of the bearings. So i cooked a bearing is about 15 miles of driving my talon. I would HEAVILY advise if you are going to change pistons in one of these engines to remove it COMPLETELY from the Talon and build it on a bench. No measurement is accurate laying on your back on the garage floor. Pull the crank, measure the journals and install new bearings when you pull a rod. When you are talking about tolerances down to the ten thousanth for oil clearance you need to make 100% sure you have those right. Also that little crank closed ring compressor is garbage. If you are having an engine built and you see one of those run for your engines life. They never work right on performance engines with stainless rings. You want to use a Wiseco tapered compressor ring with NO seams. People fail to realize these are high performance engines. Especially when you are adding boost. Building it in chassis on the garage floor is unacceptable. When you go to get an engine you need to ask to see, piston rings, bore gauge measurements, journal measurements, oil clearance on the rod bearings. If they cant AT LEAST give you all of that, RUN.

Thx this helped alot...

That leak didnt fix itself. The oil level is low and stopped leaking out. Its a common situation on small diffs on bikes and buggies. If the seal goes it could have been a piece of dirt or if it keeps going the diff bearing is bad

My OCD won't let me pay attention with that machine so dirty.

Surely one can get away with slow driving and maneuvering on concrete or asphalt… like in a driveway/garage scenario right?? I still have the light stock tires and wheels. After I wash my unit I may also take it on a quarter mile zip in the neighborhood just to dry it off. I appreciate the video

do you have any towing capability

It stopped leaking because it is empty

They look awesome !!!

Seems kinda ghetto to be building a motor in-place rather than on a bench.

What have you used your trailer hitch for? Ty

Wow I find this video now. I tried several mirror mounted to my a pillar light brackets that I could never make work with the upper doors. So I just broke down and bought the camera rear view mirror. I prob will still get these mirrors. Nice find

How much of a difference do you notice over stock?

Nice looking setup Russell, them brakes look good and appear to be high quality. Do you know if they offer them in blue? Thanks for another informative video, we were beginning to suffer from withdrawal (and still miss your adventure vids)! Happy new year btw.

I watched this when the video was new. Do you still have the 2019? How many miles are you up too now?

Great job. Very clear and informative. Thank you.

It worked! Thank you very much, very valuable and informative!

Would have been a better video if you pretended people were dumb and never changed an axle in their life which is why they come to you tube. Wish you filmed every step showing the process which helps those who don’t understand, and prevent making costly mistakes. Wanted to see you put the grease in, beat the axle out, put the axle back in, tear apart suspension parts, etc. Gonna search now for a more thorough video.

Wow, what a great review on a talon spoke nothing, but facts, minor issues that you could encounter still a great machine no money spend on belts jst like a Yamaha YXZ 1000r Transmission very similar your the man you should check out the YXZ and compare transmission see the whats different

Russell did you transfer this over to your 4 seater? Eibach says its made for the 2 seaters.

Hey make some more videos! All your videos are great and very informative!

Nice update on the talon it will be my next purchase I bought a RZR XP 1000 in 2016 what a money pit

I watched only a little bit of the engine build and it was a hack job.

The Talon seems to be similar to my Carrera; very solid in stock form, even if you run it hard, and a hand grenade if you tweak the power.

A guy came into our cafe..said he met you..pretty cool..